Cross Section,of a Gallen,
- Thread starter monica
- Start date
well some progress on this one,happy so far,have the outer/inner,hull planked to first floor,
will need to lower both I,have,as from the bottom to the bottom beam is 70mmwhich is far to much,I think ?
so will lower it to 50mm,then the high of 40mm to the next deck is to high,so will lower to 35mm as you can see,
of the figure,and she is on a 10mm milk bottle top, O.o
then that way it the texture space,maybe that of a man of war,with 5 decks 9_9
I will need to wait and get the cannon,for fit with the planking,and also the grates over the cargo holes,
which will be Friday or sat,when I,get to Nic,s
well hoping you like the progress,takes a long time,cutting each bit, o.O
will need to lower both I,have,as from the bottom to the bottom beam is 70mmwhich is far to much,I think ?
so will lower it to 50mm,then the high of 40mm to the next deck is to high,so will lower to 35mm as you can see,
of the figure,and she is on a 10mm milk bottle top, O.o
then that way it the texture space,maybe that of a man of war,with 5 decks 9_9
I will need to wait and get the cannon,for fit with the planking,and also the grates over the cargo holes,
which will be Friday or sat,when I,get to Nic,s
well hoping you like the progress,takes a long time,cutting each bit, o.O
Last edited by a moderator:
K
kintosh
Guest
Looking good
Bob
Bob
You are doing a fantastic job so far Monica
D
Deleted member 4539
Guest
Nice planking work Monica.
Looking forward to more.
Looking forward to more.
Attention to detail not slow Monica
ta Ralph,Stuart,for the nice comments,one this one,I,m enjoying it as well, :D
your so right Stuart,and some times,just need to sit back and look,and then back to research as I have no real plans, O.o
your so right Stuart,and some times,just need to sit back and look,and then back to research as I have no real plans, O.o
a bit more done today,started the deck planking and have them at there highs, O.o
ran out of wood as the sheets were only 75mm w of the 1.5 mm and not 120mm like the 2mm,so need to
get 5 more sheets to finish of the planking inside/out :/ ,bring down the upper hull thinness in/out to 1.5mm
as I still need to get the measurements of the cannons, O.o which may not be this week,as the other half,wont's
me to do things on both friday and sat,and there the only two days a week Nic is open, >
well hopping your liking the progress, 9_9
ran out of wood as the sheets were only 75mm w of the 1.5 mm and not 120mm like the 2mm,so need to
get 5 more sheets to finish of the planking inside/out :/ ,bring down the upper hull thinness in/out to 1.5mm
as I still need to get the measurements of the cannons, O.o which may not be this week,as the other half,wont's
me to do things on both friday and sat,and there the only two days a week Nic is open, >
well hopping your liking the progress, 9_9
Really like it Monica,a lot of nice work going into this project keep it up.
nice build
nice build
K
kintosh
Guest
Very nice Monica good to see the construction coming along.
Bob
Bob
S
steve5
Guest
this looking really nice monica ,can't wait to see the next installment
thank you,and very much appreciated,Jim,Joe,Steve,so glad your liking it so far, :D
well I will be able to get a cannon tomorrow I hope, O.o ,and a couple of other things I need to work out placements,of the like,
of stairs,and down to the cargo hull,and each deck,and how I,m going to fit around the mast,so back to doing some research on that side of things, 9_9
well I will be able to get a cannon tomorrow I hope, O.o ,and a couple of other things I need to work out placements,of the like,
of stairs,and down to the cargo hull,and each deck,and how I,m going to fit around the mast,so back to doing some research on that side of things, 9_9